Benchmarking nForce3-250GB

Before we benchmark nVidia's new nForce3-250Gb, we needed to decide exactly what we were going to test. There were several areas of particular interest:

How does nForce3-250Gb compare to other chipsets that we have tested? In this case, the FX5950 video card was removed and our standard ATI 9800 PRO 128mb video card was installed. So that results could be truly compared to previous benchmarks published at AnandTech, the 3400+ was replaced with the 3200+, which we have used for virtually every Athlon 64 board that we have tested. In the interest of consistency, we also replaced the 512MB of 2-2-2-5 memory with 1GB of memory (2 x 512MB) that also ran fine at 2-2-2-5 timings.

How does nForce3-250Gb perform with top components? Is the nF3-250Gb a better performer with an nVidia FX5950 Ultra? Here, it would not have been comparing apples to run ATI benchmarks with the 9800 PRO, since the 9800 XT is the current top-of-the-line. So, full benchmarks were run with both the nVidia top-line 5950Ultra and the ATI top-line 9800 XT. To provide a sanity check, we also ran a full series of benchmarks with the SiS 755 chipset, a 3400+, and the ATI 9800 XT. Since we had found the SiS board to be one of the fastest that we have tested, we wanted to see if nF3-250 benchmarks with ATI were comparable to the best performance we had seen with ATI on Socket 754. If nForce3-250 only performs comparably to the best with a 5950U, the utility of the chipset is somewhat limited. However, if nF3-250 performs just as well as the best with ATI - and even better with 5950U - then the 5950U performance is a nice bonus.

nForce3-250Gb: Stress Testing Performance Test Configuration: Chipset Comparison
Comments Locked

46 Comments

View All Comments

  • Brickster - Monday, March 29, 2004 - link

    Can one expect the following from nf3-250?

    -939 Mobo
    -DualChannel
    -PCI-X

    Any other chipsets for this?
  • amalinov - Monday, March 29, 2004 - link

    "Certainly, we will see 4 DIMMs, or two matched pairs, on the dual-channel nForce3-250Gb Ultra version of this chipset."

    again totaly unconnected with reality.
    in A64/Opteron the chipset has nothing to do with memory support. How much DIMMs are supported depends on CPU, mainboard and BIOS ONLY!
    There will be NO DUAL CHANNEL nf3-250Gb-Ultra. Just like nf3-250Gb IS NOT SINGLE CHANNEL.
    There will be DUAL CHANNEL S939 Athlon64 CPU.

    Also, another topic not well understood at Anandtech, Tom's, etc.: A64/Opteron FSB speed, HyperTransport speed, etc. - they (the writers) are mixing up clock frequency in MHz, data frequency in DDR and MHz, bandwith in GB/s. They think FSB and HyperTransport is the same thing. They think that HyperTransport is 800MHz (or maybe 200MHz "quadrupelt") - maybe becouse of similarity with P4. They think that their nf3-250Gb has a "250MHz FSB". They don't explain to the users on what depends the memory clock in a A64 system. They think that "Dual CPU support" is a feature of the chipset.
    Shame on you!
  • Diogenes2 - Monday, March 29, 2004 - link

    I remain puzzled about the continuing declaration by Anandtech about the lack of AGP locks on NF3-150 boards..

    I have no way to confirm it ( with O-Scope, etc. )at this time, but I am running 265 FSB on my Gigabyte GA-K8NPRO, and having no problems with my Saphire 9800 Pro.. This was not the case with the KT800 board I experimented with for a while, which would not tolerate an FSB above 225, as far as AGP was concerned..


    I recommend that when the NF3-250 boards hit the shelves, buyers take advantage of price drops on NF3-150 offerings.. I don't see the modest performance gains of the NF3-250 as anything to get excited about..
  • amalinov - Monday, March 29, 2004 - link

    just 2 lines below, another error:
    "nVidia includes the hooks for AC '97 6.1 audio in nForce3-250"
    6.1? Don't you mean 5+1 ("6-channel 5.1")????
    OK. This can be a typo-mistake, but when you add all typos, totaly wrong infos, etc. - it is too much to bear!
  • amalinov - Monday, March 29, 2004 - link

    "Even with the memory controller on the chip, there is only so much real estate practically available on a single-chip chipset. "
    What???? This is not true! Where did you get such information?

    SiS745, anyone? Single Chip: AGP+DDR memroy+PCI+UATA+AC97+...
    also, current 0.13um, 0.15um is more advanced than SiS745.
    Other single chip: ALi M1689, SiS630, SiS540
    There IS enough real estate for a SoundStorm APU.
    The problem can be pin-count, but is not.
    Give us the area in mm2 and production technology in um of nforce3, nforce2 IGP, nforce2 MCP-T.... then can we speak.
    Also give for comparation other chipsets - north&south&singlechip, other CPUs, other GPUs... give numbers for total transistors, total pins...

    Generaly I think that the quality of articles in Anandtech and Tom's Hardware has declined VERY MUCH and is below acceptable now. Once these two were my favorite sites. Now I visit them only becouse they are big and so get the newest stuff and make MANY benchmarks. But if you need information about internals of a component and not its speed - they will most likely give you WRONG information. There are many other mistakes in mainboard and chipsets and other articles that start to annoy me...
  • tagej - Monday, March 29, 2004 - link

    I do not find it surprising at all that most customers don't care about the sound storm stuff. After all, the vast majority of PC users (outside of the geek market of course) have their PC hooked up to $9.99 basic speakers -- sound storm is not going to make a difference at all, and is simply not a selling point.

    The 250Gb certainly looks sweet at this point... I'll be watching closely to see how the first retail boards do.
  • aak97 - Monday, March 29, 2004 - link

    Just wanna know, did the nForce3-250Gb ref board comes with any WinXP 64bits drivers? I'm sure a lot of people (including myself) will be interested in some benchmarks on the Preview version of WinXP 64bits.
  • Foxbat121 - Monday, March 29, 2004 - link

    #4,

    The "customer" in the survey probably refers to nVidia's largest OEM like HP, eMachine etc. These companies only care about save a few $$ and probably only chose nForce2 without SoundStorm.

    #7,

    The whole point of SoundStorm is to use Dolby Digital encoding and output everything throught digital sound output where analog codec chip does not get in to the play. If you use analog ouput, you will be better of with a sound card.
  • KHysiek - Monday, March 29, 2004 - link

    Now with Intel adding Azalia high lever audio to it's boards NVidia looks clearly dumb with it's chipset w/o Soundstorm.
  • clemedia - Monday, March 29, 2004 - link

    "On the other hand, Soundstorm offers high quality 3d audio rendering, but it is _ALWAYS_ paired with that SAME crappy Realtek ALC650 chip, which offers lousy analog output quality"

    Apparently you COMPLETLY overlooked the fact that most (all, AFAIK) SoundStorm boards offered digital output which bypassed those codec's completly. Which just happens to be EXACTLY what I use, and was a major selling point, allowing me to send out my DD/DTS signal to my amp for DVD's as I use for regular computer use. VERY handy.

    I would have no problem switching to something else if they offed a good DICE solution. (I think C-media makes a software DICE chip, but I would rather go with something better)

Log in

Don't have an account? Sign up now